pelton turbine diagram

Pelton Turbine Construction, Working and Design

Pelton Turbine

  • What is a Pelton Turbine?

Pelton Turbine is a Tangential flow impulse turbine in which the pressure energy of water is converted into kinetic energy to form high speed water jet and this jet strikes the wheel tangentially to make it rotate. It is also called as Pelton Wheel.

Also Read:

Parts and Their Functions of Pelton Turbine

Different parts and their functions of Pelton turbine are as follows.

Different Parts of Pelton Wheel Turbine

Fig 1: Parts of Pelton Turbine

  1. Nozzle and Flow Regulating Arrangement
  2. Runner and Buckets
  3. Casing
  4. Braking Jet

1.Nozzle and Flow Regulating Arrangement

The water from source is transferred through penstock to which end a nozzle is provided. Using this nozzle the high speed water jet can be formed. To control the water jet from nozzle, a movable needle spear is arranged inside the nozzle.


Fig 2: Nozzle and Flow Arrangement

The spear will move backward and forward in axial direction. When it is moved forward the flow will reduce or stopped and when it is moved backward the flow will increase.

2.Runner and Buckets

A Pelton turbine consists of a runner, which is a circular disc on the periphery of which a number of buckets are mounted with equal spacing between them. The buckets mounted are either double hemispherical or double ellipsoidal shaped.

Runner and Buckets of Pelton Wheel

Fig 3: Runner and Bucket

A dividing wall called splitter is provided for each bucket which separates the bucket into two equal parts. The buckets are generally made of cast iron or stainless steel or bronze depending upon the head of inlet of Pelton turbine.


The whole arrangement of runner and buckets, inlet and braking jets are covered by the Casing. Casing of Pelton turbine does not perform any hydraulic actions but prevents the splashing of water while working and also helps the water to discharge to the tail race.

Pelton Turbine Casing


Fig 4 : Pelton Turbine Model With Casing

4.Braking Jet

Braking jet is used to stop the running wheel when it is not working. This situation arises when the nozzle inlet is closed with the help of spear then the water jet is stopped on the buckets. But Due to inertia, the runner will not stop revolving even after complete closure of inlet nozzle.

To stop this, a brake nozzle is provided as shown in figure 1. The brake nozzle directs the jet of water on the back of buckets to stop the wheel. The jet directed by brake nozzle is called braking jet.

Working of Pelton Turbine

The working of Pelton turbine is as follows:

  • The water is transferred from the high head source through a long conduit called Penstock.
  • Nozzle arrangement at the end of penstock helps the water to accelerate and it flows out as a high speed jet with high velocity and discharge at atmospheric pressure.
  • The jet will hit the splitter of the buckets which will distribute the jet into two halves of bucket and the wheel starts revolving.
  • The kinetic energy of the jet is reduced when it hits the bucket and also due to spherical shape of buckets the directed jet will change its direction and takes U-turn and falls into tail race.


Water Jet striking Pelton Wheel Buckets

Fig 5: Water Jet striking Pelton Wheel Buckets

  • In general, the inlet angle of jet is in between 1o to 3o, after hitting the buckets the deflected jet angle is in between 165o to 170o.
  • The water collected in tail race should not submerge the Pelton wheel in any case.
  • To generate more power, two Pelton wheels can be arranged to a single shaft or two water jets can be directed at a time to a single Pelton wheel.

Design aspects of Pelton Turbine

Following are the aspects to be considered while designing the Pelton wheel turbine.

  1. Velocity of jet
  2. Velocity of wheel
  3. Angle of deflection of jet
  4. Mean diameter of the wheel
  5. Jet ratio
  6. Bucket dimensions
  7. Number of jets
  8. Number of buckets


Pelton wheel

Fig 6: Pelton Wheel

Bucket Dimensions

Pelton Turbine buckets

Buckets dimensions are designed in such a way that its breadth should be 3 to 4 times of diameter of jet, length should be 2 to 3 times of diameter of jet and thickness should be 0.8 to 1.2 times the diameter of jet.